AV8000S Flatbed/ ADF Color Document Scanner User's Manual ( D/N: 250-0351-0 Rev. 2.0 )
2-3 2.1.2 LOCKING THE SHIPPING SWITCH Whenever you need to move the scanner to a new location it is advisable to lock the shipping switch to avo
2-4 2.3 SETTING SCSI TERMINATOR AND SYNC The scanner is equipped with a built-in terminator switch on the rear of the scanner. (See Figure 2-2/2-
2-5 Figure 2-2 Terminator ON/OFF Host PC scanner SCSI Device Term. Term. Host PC scanner Term. (Terminator Off) (Terminator On)
2-6 2.4 DOCUMENT LOADING i). Place the document to be scanned onto the document glass face down. ii). Position the document so that the upper-
2-7 2.5 CONNECTING THE CABLE i). Turning the Power Off Follow the following picture to connect the power cable. Depress the side marked “0” to tu
3-1 3. SOFTWARE INSTALLATION & OPERATION To run the scanner at rated speed recommended , you must have the following minimum requirements: v I
3-1 3.1 SCANNING OPERATION There are two methods to perform scanning operation: Scanning with the user interface and Pressing the Scan button on
3-2 6. Select the scanning method you want to use on the Scan Method drop-down menu. 7. Select the mode you want to use for your scans on the Im
4-1 4. USING THE BUTTONS The following chapter applies only to PC users. 4.1 CUSTOMIZING YOUR BUTTON SETTINGS After you have successfully install
4-2 preferences.
ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pur
4-3 1. Image Type: Choose a proper image type. 2. Scan Size: Choose your scan size from Letter, A4, or Business Card. 3. Resolution: Choose
4-4 4.2 USING THE SCAN BUTTON 1. Press the Scan button. Scan and load your scanned image to your image editing software application. 2.
5-1 5. USER INTERFACE 5.1 SCAN METHOD Select how you want to scan on the Scan Method drop-down menu. Flatbed— use this setting if you are using
5-2 5.2 DETERMINING YOUR RESOLUTION A good control of the resolution results a satisfactory detail of an image that scans. The resolution is
5-3 Tips: 1. For your information, an A4 size color image scanned at 300 dpi at True Color mode consumes approximately 25 MB of disk space. A
5-4 5.3 SELECTING A PROPER IMAGE TYPE Select image type through the mode from the scanner user interface for your own purpose. Each image type
5-5 Halftone In addition to the black and white display, Halftone simulates gray scale by using different size of dots. Particularly when you vi
5-6 8-Bit Gray A single-channel image consists of at least 256 shades of gray. An 8-bit scanner produces a grayscale image with 1024 shades of gr
5-7 8-Bit Color an 8-Bit Color image provides 256 color hues in the image. The file size of a 256 color image is 1/3 the size of a 24-Bit Color ima
5-8 5.4 ENHANCING YOUR IMAGE Brightness: Adjusts the lightness or darkness of an image. The higher the value, the brighter the image
iii Safety Regulation EMI Regulation UL, C-UL, TUV/GS,CB certificate FCC Part 15 Subchapter J Class B DOC Class B (Canada) CE, VCCI, C-TICK, BSM
5-9 5.5 CONTRAST Adjusts the range between the darkest and the lightest shades in the image. The higher the contrast, the bigger the differe
5-10 5.6 INVERT IMAGE The invert command reverses the brightness and the color in the image. For color images, each pixel will be changed
5-11 5.7 MIRROR Click on the Mirror button to reverse the image (create a mirror image). Mirror function is off Mirror function is on
5-12 5.8 PREVIEW AUTO-AREA Clicking on the Preview Auto-Area button automatically crops the preview scan area to the previewed document. This wil
5-13 5.10 DESCREEN Click on the Descreen button to access a drop-down menu that allows you to specify the type of document you are scanning in or
5-14 5.12 COLOR ADJUSTMENT Click on the Color Adjustment button to enable the button for the Hue, Saturation, and Lightness feature. NOTE: The A
5-15 This feature is available when 8-Bit Gray, 8-Bit Color, or 24-Bit Color is selected on the Image Type drop-down menu. Highlight refers the lig
5-16 Curves When you select the Curves button, a dialog box appears that allows you to adjust the midtone of the image without losing details in
5-17 Color Balance When you select the Color Balance button, a dialog box appears that allows you to adjust the color of the image so that it comes
5-18 Hue— specify a value in the Hue box to adjust the hue up to 360° by clicking on the desired color on the color wheel or selecting a setting on
iv Wichtige Sicherheitshinweise 1. Bitte lesen Sie diese Hinweis sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3.
5-19 Color Drop-out This feature is available when Black and White, Halftone, or 8-Bit Gray is selected on the Image Type drop-down menu. Click on
5-20 Custom Settings Click on the Custom Settings button to access a dialog box where you can save your scan settings and configuration setting
5-21 Configuration Settings The Configuration Settings tab allows you to customize some special settings. Energy Saving Mode— check the Enable bo
5-22 5.15 MISCELLANEOUS Width : Shows the current image width. Height: Shows the current image height. Size: Shows the current file size of th
5-23 Preview: Click on the Preview button to scan a document so you can review the scanned image. This allows you to specify an area to be scann
6-1 6. MAINTAINENCE 6.1 CLEANING THE ADF The scanner is designed to be maintenance free. However, it still needs to be cleaned occasionally to
7-1 7. TROUBLE SHOOTING The scanner will automatically perform a simple self-test each time it is turned on. This will help spot major system error
7-2 Question: Paper becomes jammed during scanning. Answer: a) Open the ADF unit. b) Pull out the jammed paper carefully. c) Close the ADF
7-3 Question: Paper becomes skewed in the scanner. Answer: a) Check the feeding roller condition; do the cleaning if necessary. b) Use th
7-4 Question: When I power on the scanner, the lamp does not light. Answer: The possibilities are as follows: a) The lamp is out of or
vi Table of Contents 1. INTRODUCTION...1-1 2. INSTALLATION...
7-5 Question: The scanned image always comes out to be too dark. Answer: a) Use your application to modify the Gamma setting to 2.2 and 1.8 f
7-6 7.2 ERROR MESSAGES 1. When the Paper In/Paper Jam lamp on the front panel turns orange steadily, paper jam in the ADF happens. Please r
8-1 8. TECHNICAL SERVICE Technical support for Avision scanner is provided at Avision Technical Assistance Center (ATAC). Before contact with ATAC
9-1 9. SPECIFICATION Model: AV8000S Item SPEC. Optical Resolution 600 x 1200 dpi Max. Scan Area 11.8” x 17” Physical Dimension 589 x 428 x
10-1 10. AUTOMATIC DOCUMENT FEEDER(ADF) INTRODUCTION The AV8000S Automatic Document Feeder (ADF) is a very convenient addition to your current AV80
10-2 10.2 ADF SCANNING Multiple documents can be fed automatically using the ADF. i). To prevent occasional paper jam when automatically feedi
10-3 10.3 CLEANING THE ADF From time to time the pad assembly and feeding rollers may become contaminated with ink, toner particles or paper dust.
10-4 10.4 REPLACING ADF FEEDING MODULE After scanning approximately 20,000 pages through the ADF, the separation pad may be worn out and you may e
vii 5.14 ADVANCED SETTINGS...5-14 5.15 MISCELLANEOUS...
1-1 1. INTRODUCTION Congratulations on your purchase of AV8000S scanner. Before you install and operate the scanner, please take a few minutes to r
2-1 2. INSTALLATION Please unpack the scanner carefully, and check the contents against the checklist. If any items are missing or damaged, pleas
2-2 2.1.1 UNLOCKING THE SCANNER i). Carefully place the scanner on a table. ii). Unlock the scanner by moving the lock switch on the left side
Commentaires sur ces manuels